Installation Guide

How to Install an RPO System

A day-by-day plan for installing run-pass options. Clear QB reads, simple OL rules, and a system that forces the defense to be wrong on every play.

Day 1: The Read Key Concept

Every RPO starts with a single question: which defender does the QB read? On Day 1, teach the concept before you install a single play. The QB reads one unblocked defender. If that defender commits to stopping the run, the QB throws. If that defender drops into coverage or stays put, the QB gives the ball to the running back. One read, one decision.

Use a whiteboard to show the concept against a basic four-man front with two linebackers. Circle the read key. Show the QB what "give" looks like and what "throw" looks like. Then take it to the field. Have a coach or a scout-team player stand at the read-key position and flash either a run fit or a pass drop. The QB watches, decides, and executes.

Speed is critical. The QB must make the decision before the offensive line crosses the line of scrimmage. If the throw comes late, you get an ineligible-man-downfield penalty. Every rep on Day 1 should emphasize a quick, decisive read. No double-clutching. No hesitation. Read, decide, execute.

Day 2: Glance RPO with Inside Zone

The glance RPO is the best first install because it is simple and effective. Pair it with inside zone. The OL blocks inside zone exactly as they normally would. The running back takes his zone track. One receiver on the play side runs a glance route, which is a quick one-step slant at three to five yards depth.

The QB reads the play-side inside linebacker. If that linebacker fills his run gap, a window opens behind him in the passing lane. The QB throws the glance into that window. If the linebacker sits or expands toward the receiver, the QB gives the ball on inside zone. The beauty of the glance is that the throw is short and fast, so the OL has time to block the run without worrying about downfield penalties.

Rep the glance RPO against a scout defense with a live read key. Tell the scout-team linebacker to randomly fill or sit. The QB reads and reacts. By the end of Day 2, the QB should be throwing the glance with confidence when the read is there and handing off without hesitation when it is not.

Day 3: Bubble RPO and Perimeter Reads

The bubble RPO expands the system to the perimeter. Pair inside zone with a bubble screen to the field side. The QB now reads the flat defender instead of the linebacker. If the flat defender squeezes inside to play the run, the QB throws the bubble to the receiver who is already running his screen path. If the flat defender stays wide, the QB gives the inside zone.

The blocking for the bubble must be crisp. The outside receiver blocks the corner. The slot receiver catches the bubble and turns upfield. Timing matters here more than on the glance. The bubble throw is longer, so the QB needs to make the decision a fraction of a second earlier. If the throw is late, the defense recovers and the screen gets blown up.

After the bubble is installed, you can also add the pop pass. The pop is a quick throw to a tight end or running back who leaks out over the middle after a play-action fake. The read key is the same concept, just a different defender. By Day 3, your QB should have two RPO tags he can execute off inside zone.

Day 4 and 5: OL Rules and Full Team

The offensive line blocks run on every RPO. This is the non-negotiable rule. Linemen do not change their technique based on whether the QB gives or throws. They fire off the ball, execute their zone steps, and work their combos. The throw is the QB's job. The OL's job is to move people.

The challenge for the OL is staying behind the line of scrimmage long enough for the throw to leave the QB's hand. On inside zone RPOs, the linemen naturally stay close to the line because they are working lateral combos. On power-based RPOs, the pulling guard gets downfield faster, so the QB has less time to throw. Match your RPO tags to your run plays based on OL displacement timing.

Day 5 is full team with a defense that is trying to stop both the run and the pass. This is the real test. If the defense loads the box, the QB should be throwing RPOs all day. If the defense respects the throw and plays soft, the inside zone should gash them. The whole point of an RPO system is to make the defense wrong no matter what they do. If your QB is making the right reads, that is exactly what happens.

Glance RPO

The most common first-install RPO. The QB reads the play-side linebacker. If the backer fills the run, the QB throws the glance route behind him. If the backer sits, the QB gives the ball.

Bubble RPO

A perimeter read paired with inside zone. The QB checks the flat defender. If the flat defender squeezes inside, the QB throws the bubble screen. If the defender stays wide, the QB gives the run.

OL Rules

Offensive linemen block run on every RPO. They cannot go downfield on a pass play, so the throw must happen within one second. OL technique does not change between give and throw.

Make the defense wrong on every snap.

RPOs let you run and throw off the same play. The defense has to guess. Your QB just has to read.

Install your scheme in Blitz.